Our Way is the Right Way to Car Detailing
Take away floor mats and start to vacuum the floor, upholstery, mats, trunk, rear parcel shelf and the dash. The seats must be slided the whole way forward and then thoroughly vacuum the carpet below.
Our management advise is you to start from the top and proceed your way down because dust or dirt that has gathered at the top could fall down.
Then you have to start to clean carpet or upholstery stains. You should to apply a foam cleanser and gently brushing it in with a wet cloth or sponge. Wait for a few minutes before drying with a towel. Repeat again if the stain still shown. Wash the surface with a wet sponge and do a final blotting.
Try to take as much moisture from the fabric as possible. Too much moisture may bring molding and/or mildew.
If you have to repair carpet burns or small permanent stains, try to cut from an unseen area, such as underneath the seat.
Clean and wash rubber floor mats and dry them. Use a non-slip dressing so that the driver’s feet don’t slip and slide while they apply braking.
In order to pull out dust from the buttons and crevices on the dash and interior doors, use compressed air and detailing brushes.
Hard interior parts must be wiped out with a mild all-purpose cleaner.
Clean car air vent grilles with detailing brushes. In order to pick up dust and dirt efficiently, the detailing brushes should be from a super-absorbent material like microfiber cloth. Using spray-on vinyl dressing onto the vent grilles will produce brand new look
When it comes to clean the seats, use shampoo. The essential part of a good detailing is cleaning the seats. Study the seat before choosing the cleaning method. Once you finish cleaning, you may to vacuum out the seats again.
Use wet-vac extraction machine for interiors with nylon or other cloth and can be shampooed too. Dry up the cloth after extraction.
Apply special leather or vinyl cleaner when cleaning leather or vinyl interiors then hit softly with a leather brush.
If you want the leather on the seats to look visually appealing, the right way is to condition them, so they not to begin to crack
The windows and mirrors should be sprayed with glass cleaner and wiped clean. If the gauge cover is made of plastic, use plastic cleaner
Exterior Car Detailing Starts with Brushing Wheel Rims
As this is where most of the dirt, grime, and grease accumulates. Use a wheel brush and wheel cleaner. Wait for material to penetrate wheel rims for a few minutes before brushing.
Use acid-based cleaners responsibly only on rough-textured alloy wheels, never on polished alloy wheels or clear-coated wheels.
Sparkle up chrome wheels with metal polish or glass cleaner.
Car detailing is an art and we suggest that washing the tires must be performed with whitewall tire cleaner (even if you have black-walls). Don’t forget to apply tire dressing. There are two major categories: solvent-based and water-based. If you let the dressing soak in then there is a glossy finish or wipe it on and off with a cotton cloth for a matte look.
Electronic components should be attached in plastic under the hood. Spray degreaser on every part and then use pressure washer.
Cover non-metal parts under the hood with vinyl/rubber protectant. Let it to soak in for shiny finish and wipe it off for dull one.
As Auto Body Shop Toronto recommends, check your cleaners that contain ammonia and/or vinegar before applying to tinted windows. Less worry about factory tinting because is built into the glass itself, but after-market tinting is more degradable.
Your car’s exterior should be washed with a car wash soap and a deep-pile terrycloth microfiber towel which will trap contaminants.Have two buckets — one with regular water, the other with sudsy cleaner. Work from the top down. Wash and rinse a section at a time. Make sure the soap is not to drying.Do a final rinse to minimize spots.Dry up with a chamois or terry cloth towel; do not let air-dry or soap spots will form.Glass cleaner must be used to clean windows on outside which make them shine and reflect.
Clean the wheel wells with an all-purpose cleaner and high-pressure water spray. You can employ a vinyl dressing to the walls for a glittering effect.Finally, according our auto detailing Toronto companies, polish or wax should be applied with a dual-action polisher or by hand.
Professionals use polish for a glossy look and wax as a protect ant.
One should pay attention to door jambs, door hinges and behind bumpers, which needs to do by hand.
Let it dry to a haze. Usually, car detailing is finished by buffing with the machine. If there is the hard-to-reach areas then buff by hand.
205 Hilda Avenue #512
North York, ON M2M 4B1